WAVLINK M.2 NVMe SSD Hard Drive Enclosure USB C External Hard Drive Case

Description: Type-C Thunderbolt 3 to NVMe SSD Classic( Enclosure Only ) This gadget turns your NVMe SSD into an external storage solution. It works over Thunderbolt 3 host interface at up to 40 Gbps bus bandwidth, so you can take full advantage of the latest PCIe 3.0 x4 NVMe SSDs. Integrated heatsink works together with aluminum casing and side vents to efficiently dissipate heat and prevent throttling. The included Thunderbolt 3 cable has an anchoring clip for secure connection to the enclosure's Thunderbolt port. Plus, leather-like covering on the enclosure casing gives enhanced comfort and control when this enclosure is held in hand. Small and portable storage, mixed with aluminum alloy design providing NVMe SSD giving maximum theoretical speed up to 3,940 MB/sThunderbolt 3 provides speed up to 40Gbps, allows NVMe SSDs to achieve peak performance, 6-7 times the sequential read/write speeds of SATA.Heat sink integrated giving the best ventilation for NVMe SSD running at high speed.0.5m Thunderbolt 3 pigtail cable (Intel Certified) ensure NVMe SSD best performancePlug-and-Play connection, no installation needIn the Box1x Thunderbolt 3 NVMe External SSD enclosure1x Thunderbolt 3 protocol special high-speed data cable 50cm (Intel Certified)1x Heat SinkInstallation Tool1 x Protect Pouch1 x Quick Start GuidePushing the Boundaries of Performance High-speed Thunderbolt 3 NVMe m Key m.2 SSD enclosure, support PCI-E×4, theoretical transmission speed up to 40Gb/s (MAX).Not all Thunderbolt 3 computers are x4 full speed, part of which maybe x2.Wavlink Thunderbolt 3 NVME SSD Enclosure Hardware accelerated architecture enables very low latency and low powerScalable NVMe architecture enables an efficient qualification process and maintains significantly higher performance over SATAHeat sink integrated giving the best ventilation for NVMe SSD running at high speed.Plug and play. No need for external power.Attention NVMe SSD thickness below 2.5mm.Socket low profile design for single sided NVME SSD only.System Requirements and CompatibilityOperating system compatibility: Windows, macOS 10.13 later. Due to the variety of computers used by customers, the computers used by customers may not have a Thunderbolt 3 port. This product is only suitable for computers with Thunderbolt 3 port, not for ordinary USB C ports. Compatible for MacBook Pro 2016+/MacBook Air 2018+ and Thunderbolt 3 Laptops PC. This SSD is plug and play, you can easily use it with your laptops to read and write data, no need of other driver or installation.Not compatible with: M.2 SATA SSDs, M.2 PCIe AHCI SSDs, or other M.2 non-NVMe devices. Scalable NVMe architecture, the NVMe SSD enclosure is breaking through performance limits of client computing, enabling partners to support higher storage applications in today’s mobile and ultra-thin computing markets. This product only supports Type C interface computers with Thunderbolt 3 protocol,and doesn't support ordinary Type C interface computers without Thunderbolt 3 protocol. Please confirm whether the computer Type c interface has Thunderbolt 3 logo. Suitable for 2.5mm thickness,22x80mm M.2 NVMe SSDEasy to Use This SSD is plug and play, you can easily use it with your laptops to read and write data, no need of other driver or installation. Only compatible with NVMe SSD thickness below 2.5mm, socket low profile design for single sided NVME SSD only, if the thickness of SSD is more than 2.5mm, the heat sink will protrude during the installation process, resulting in damage to the SSD.High Performance PCs and LaptopsGamingUltra HD or 4K Video CreationVR Content CreationHigh-Bandwidth Corporate Computing40Gbps-for Thunderbolt 3/4 *One-Click Offline Clone: WAVLINK's hard disk enclosure is a dual-bay device that supports one-click cloning from the source disk to the target disk. You can also change the cloning direction through the toggle switch. Be sure to disconnect the data from your computer before starting cloning. *Flexible Storage Expansion: The dual-bay hard drive enclosure supports up to 8TB, which equates to two 4TB SSDs. Equipped with a C to C power cord, USB-A adapter and OTG support, it can help you connect your mobile phones, tablets, laptops, desktop computers and other devices to expand your storage capacity. *High Speed Transmission: USB-C supports a maximum transmission speed of 10Gbps. High-speed reading and writing are 935MB/s and 729MB/s respectively. Just plug and play and you can quickly transfer large-capacity tasks such as pictures, videos, files, games, etc. *Wide Compatibility: The dual-bay supports SSDs of various sizes, such as 2280/2260/2242/2230 and applicable interfaces, M and B+M keys. But it is not suitable for SSD with mSATA interface. It also comes with two silicone buckles and two thermally conductive silicone pads to secure the SSD. *Easy to Use: Metal sliding cover design, easy to disassemble and assemble, no tools required, plug and play, no need to download any driver. If you encounter any installation or usage problems, please contact our customer service staff to protect your rights.Dual Bay-w/Offline Clone-10Gbps-up to 8TB Specification: 1.Model: ST347 2.Ports: 1 x DC IN Port, 1 x USB-C Port 3.Button: 1 x Offline Cloning Key, 1 x Toggle Switch 4.Status LED(Blue): 1 x NVMe, 1 x SATA 5.Offline Cloning Indicator(Blue): 25%, 50%, 75%, 100% 6.Power Adapter: DC 5V/4A 7.Unit Dimensions: 118.1 x 73.25 x 15.78mm /4.65 x 2.88 x 0.62in (L x W x H) Compatibility Systems: Microsoft Windows 10/11; Mac 10 or later; Chrome OS; Linux; Android; Harmony OS; iPad OS; iOS. Devices: Computers with USB-C or A ports that support data transmission; mobile phones and tablets with USB-C ports. SSD: Support M and B+M key PCIe NVMe in sizes of 2230/2242/2260/2280; not support mSATA SSDs. What’s in the Package? - 1 x Dual M.2 SSD Enclosure with Offline Clone - 1 x USB-C to USB-C with USB-A Cable - 2 x Thermally Conductive Silicone Pad - 1 x DC 5V/4A Power Adapter - 2 x Silicone Buckles - 1 x Quick Start Guide Note: - Supports bidirectional cloning, cloning data offline from NVMe to SATA or SATA to NVMe through toggle switch. - Supports OTG mobile phones to read and write USB peripherals and SSD. - Please start cloning after disconnecting the data connection from the computer. - The target disk capacity must be larger than the source disk. Please check your SSD before installation. - Compatible with NVMe and SATA, not suitable for mSATA interface. Please confirm your hard drive type before purchasing. Leading the Industry with 40Gbps USB4 Speeds - Equipped with a USB4 port, the WAVLINK enclosure offers lightning-fast data transfer speeds of up to 40Gbps for PCIe NVMe SSDs. When your computer is properly configured and your SSD is qualified, you can achieve impressive read and write speeds of up to 3800MB/s (Data sourced from WAVLINK Labs). With a capacity expansion support of 8TB, this enclosure provides ample space to store a vast collection of files, pictures, videos, games, and more. Comprehensive Cooling System - Constructed with a robust aluminum alloy case, this SSD enclosure ensures optimal protection for your SSD while prioritizing efficient heat dissipation. The inclusion of two thermal silicone pads facilitates dual heat ventilation effects. With its sandwich-like cooling system, this enclosure effectively safeguards your SSD against overheating, ensuring stable and smooth data transfers. Extensive Compatibility - Designed to accommodate M key and B&M Key PCIe NVMe SSDs, this enclosure supports double-side SSDs in sizes of 2280, 2260, 2242, and 2230 (SSDs not included). It is also compatible with various operating systems, including Windows 7 or later, Mac OS 10.5 or later, and Linux, enabling seamless data transfer across different devices. Please note that the enclosure does not support AHCI SATA SSDs. Plug and Play & Tool-Free - With its compact dimensions of 11.6 x 5.2 x 2cm and lightweight design of 150g, this portable enclosure can easily fit into a pocket or briefcase, granting you access to extensive storage capacity anytime and anywhere. It supports plug and play, allowing for a direct connection with devices without additional drivers. Furthermore, the tool-free installation feature enables you to install the SSD without extra tools, providing convenient external storage for on-the-go use. Intelligent Chip & Multiple Protection - The advanced ASM2464PD chip ensures safe and smooth operation of the enclosure while effectively reducing SSD-generated heat. It also supports UASP and Trim, which minimize data delay and speed loss, significantly enhancing the transmission speed. Additionally, the enclosure supports S.M.A.R.T., simplifying SSD status monitoring, conserving energy, and extending the service life of your SSD.40Gbps USB4-Intelligent Chip-8TB Compatibility Notes Systems: Windows 7 or higher, Mac OS 10.5 or higher, Linux; Host: Computers with a USB-C port;(The performance might be limited on TBT3 and normal usb port. To get the advertised performance, the host should support TBT4 or USB4 and it should support 40Gbps.) SSD: Support M key and B&M Key PCIe NVMe SSDs(both one-side and double-side) in sizes of 2280, 2260, 2242, and 2230; NOT support B Key SSDs and AHCI SATA SSDs. Specification: 1.Model: WL-ST401C 2.Unit Size: 11.6 x 5.2 x 2 cm/ 4.6 x 2 x 0.8 in (WxDxH) 3.Cable Length: 25cm/9.8in 4.Unit Weight: 150g/5.3oz 5.Housing Material: Aluminum Alloy 6.LED Light: Blue In the Box -1×USB4 PCle NVMe SSD Enclosure -1×USB-C to USB-C Cable (40Gbps) -1×Silicone Buckle -1×Silicone Case -1×Pouch -2×Thermal Silicone Pad -1×Quick Start Guide (Note: the NVMe SSD is not included) Warm Tips: 1.The NVMe SSD is not included. 2.The performance might be limited on TBT3 and normal usb port. To get the advertised performance, the host should support TBT4 or USB4 and it should support 40Gbps. 3.This test result for Max.3800MB/s reading and Max.3800MB/s writing is the best result tested by our own test environment, and the specific effect is determined by the computer configuration and your SSD. 4.If the SSD is brand-new and unformatted, please perform partition installation so that the computer can read the data normally. If the SSD is formatted and has stored data, you have no need to perform partition installation because the computer can read the data normally. 10Gbps Super Speed - WAVLINK M.2 NVMe and SATA SSD external case features the JMS581X control chip and the latest USB 3.1 Gen 2 Type-C interface. It supports the UASP acceleration protocol, enabling theoretical data transmission speeds of up to 10Gbps. With high-performance NVMe or SATA media, read/write speeds can reach 10Gbps or 6Gbps. Includes a USB-C to USB-C cable and a USB-C to USB-A OTG converter, and works with USB-C/USB-A hosts. Applicable SSD Hard Drive - This M.2 enclosure is compatible with NVMe and SATA SSDs (*SSDs not included). It works with USB-C 3.1 Gen 2 or Thunderbolt 3/4 hosts, supporting speeds of up to 10Gbps, as well as USB-C 3.1 Gen 1 and USB 3.0 systems capable of up to 5Gbps. Compatible with 2230/2242/2260/2280 NVMe/SATA SSDs, but not compatible with M.2 SATA B-Key SSDs, mSATA SSDs, or M.2 PCIe AHCI SSDs. Support System - The portable enclosure is plug & play, requiring no drivers. Compatible with Windows, Mac OS, Linux, Chrome OS, iOS, Harmony OS and Android with OTG functionality. *Note that if the SSD is brand-new and unformatted, please perform partition installation so that the computer can read the data normally. Reliable & Durable - Constructed from premium aluminum alloy with ventilation holes, this M.2 adapter excels at heat dissipation, eliminating the need for a cooling fan during high-speed operation. Equipped with short-circuit, over-current, and over-heat protection, it ensures the safety of your NVMe/SATA SSD and valuable files. The LED indicator provides easy monitoring of the working status. Convenient Storage Solution - The included pouch serves as a practical storage solution for safely storing the SSD enclosure, data cable, and disassembled gadgets. This arrangement ensures they are well-preserved and organized, ready for use whenever needed.10Gbps USB 3.1 Gen 2-Supports UASP Trim-8TB Specification 1.Model: WL-ST340C 2.Unit Size: 110 x 28.7 x 10 mm/4.3 x 1.1 x 0.4in (WxDxH) 3.Cable Length: 20cm/7.9in 4.Unit Weight: 32g/1.1oz 5.Housing Material: Aluminum alloy with ABS plastic 6.LED Light: Blue Warm Reminder 1. Please choose the correct type of SSD: Compatible with M.2 PCIe M-Key/B&M-Key SSDs and M.2 SATA B&M-Key SSDs. 2. Does not compatible with M.2 SATA B-Key SSDs, mSATA SSDs, or M.2 PCIe AHCI SSDs. Not compatible with double-sided SSD cards. 3. Partition and Format: If the SSD is brand-new and unformatted, please perform partition installation so that the computer can read the data normally. In the Box 1x USB-C to M.2 SSD Enclosure 1x USB-C to USB-C Cable with USB-C to USB-A Converter 1x Thermally Conductive Silicone Pad 1x Silicone Protective Case 1x Cloth Pouch 1x Screwdriver 1x Quick Start Guide 10Gbps Super Speed : Wavlink M.2 NVMe SSD external case adopts Realtek RTL 9210 control chip and latest USB 3.1 Gen 2 Type-C interface. Support UASP acceleration protocol and support theoretical data transmission speed of up to 10Gbps. When using high-performance NVMe media, the read/write performance can reach 1000 Mbytes/sec. Includs USB-C to USB-A cable and a USB-A to USB-C OTG convertor, works with USB-C/USB-A hosts. Applicable SSD Hard Drive : M.2 NVMe SSDs (SSD not included). USB-C Gen 2 or Thunderbolt 3 hosts up to 10Gbps, USB-C 3.1 Gen 1 and USB 3.0 systems capable of up to 5Gbps. Compatible with 2230/2242/2260/2280 NVMe SSD. Not compatible with M.2 SATA SSDs, M.2 PCIe AHCI SSDs, or other M.2 PCIe devices. Support System : Portable, Plug & Play, no Driver needed and compatible with Windows, Mac OSX, linux and smartphone with OTG functionality. SSD file system must be supported on host operating system to be accessible. Reliable & Durable : Made of premium aluminium alloy with ventilation holes, Wavlink enclosure does better at heat dissipation, no cooling fan is needed for high-speed working. Built with short-circuit, over-current and over-heat protection, it ensures safety to your NVMe SSD and valuable files. The LED indicator lets you learn the working status easily. The included pouch can be used to neatly store the SSD enclosure (in the double protection of our silicone case), the data cable and the disassembled gadgets, so that they can steadily keep in good condition and be in order when needed to be used. What you get : 1x USB3.1 Gen.2 NVMe SSD Enclosure, USB-C to USB-C (10Gbps) Cable 500mm, 1x USB-A to USB-C Adapter, 1x pouch, 1x Silicone protective case, 1x Screw driver, 1x User Manual. 12-month worry free warranty (extra 6 months for registered members) and lifelong friendly technical support.10GbpsUSB 3.1 Gen 2-Support UASP-up to 2TB Warm Reminder: 1. Your computer won't recognize the actual SSD's brand with this NVME to USB Adapter, so for Samsung SSD that you couldn't use the Samsung disk cloning software 2. For the brand new SSD drive, it may not find the drive, because the brand new SSD drive should be formatted before first time using. And also need to make the SSD drive partition. One-Click Offline Clone: WAVLINK's hard disk enclosure is a dual-bay device that supports one-click cloning from the source disk to the target disk. And don't insert the wrong SSD location in the dual-disk drive; otherwise, cloning will not start. Be sure to disconnect the data from your computer before starting cloning. Flexible Storage Expansion: The dual-bay hard drive enclosure supports up to 8TB, which equates to two 4TB SSDs. Equipped with a C to C power cord, USB-A adapter and OTG support, it can help you connect your mobile phones, tablets, laptops, desktop computers and other devices to expand your storage capacity. High Speed Transmission: USB-C supports a maximum transmission speed of 20Gbps. High-speed reading and writing are 1631MB/s and 1267MB/s respectively. Just plug and play and you can quickly transfer large-capacity tasks such as pictures, videos, files, games, etc. Wide Compatibility: The dual-bay supports SSDs of various sizes, such as 2280/2260/2242/2230 and applicable interfaces, M and B+M keys. But it is not suitable for SSD with SATA or mSATA interfaces. It also comes with two silicone buckles and two thermally conductive silicone pads to secure the SSD. Easy to Use: Metal sliding cover design, easy to disassemble and assemble, no tools required, plug and play, no need to download any driver. If you encounter any installation or usage problems, please contact our customer service staff to protect your rights.20Gbps USB3.2 Gen 2x2-w/Offline Clone-8TB Specification: 1.Model: ST348 2.Ports: 1 x DC IN Port, 1 x USB-C Port 3.Button: 1 x Offline Cloning Key 4.Status LED(Blue): 1 x Source, 1 x Target 5.Offline Cloning Indicator(Blue): 25%, 50%, 75%, 100% 6.Power Adapter: DC 5V/4A 7.Unit Dimensions: 118.1 x 73.25 x 15.78mm /4.65 x 2.88 x 0.62in (L x W x H) Compatibility Systems: Microsoft Windows 10/11; Mac 10 or later; Chrome OS; Linux; Android; Harmony OS; iPad OS; iOS Devices: Computers with USB-C or A ports that support data transmission; mobile phones and tablets with USB-C ports. SSD: Support M and B+M key PCIe NVMe(target disk) and AHCI(source disk) in sizes of 2230/2242/2260/2280; not support SATA or mSATA SSDs. What’s in the Package? - 1 x USB-C 20Gbps Dual M.2 SSD Enclosure with Offline Clone - 1 x USB-C to USB-C with USB-A Cable - 2 x Thermally Conductive Silicone Pad - 1 x DC 5V/4A Power Adapter - 2 x Silicone Buckles - 1 x Quick Start Guide Note: - Supports OTG mobile phones to read and write USB peripherals and SSD. - Please start cloning after disconnecting the data connection from the computer. - The target disk capacity must be larger than the source disk. Please check your SSD before installation. - Compatible with NVMe and AHCI, not suitable for SATA or mSATA interfaces. Please confirm your hard drive type before purchasing.

Price: 18.99 USD

Location: Perth Amboy, New Jersey

End Time: 2024-11-30T10:38:13.000Z

Shipping Cost: 0 USD