PIETTA FRONTIER, PISTOLERO, GREAT WESTERN II MAGNA-TUSK™ 1P IVORY GRIPS ~ GW 2

Description: Arizona Custom GripsPIETTA SAA(Pietta Single Action Army Style Revolver Grips)* PIETTA / CIMARRON FRONTIER, PISTOLERO, EL MALO, etc.;* PIETTA / EMF GREAT WESTERN II (includes most GW II models); and * OTHER Misc. PIETTA SAA Style REVOLVERS (Davidson’s Exclusive 1873, etc.)(See below for further details)~ Exclusive ~ MAGNA-TUSK™white ivory GRIPSMilled out of a solid block of Magna-Tusk, denser and heavier than regular Ivory or Stag. See below for details.~~~~~oNE-PIECE (nO SCREWHOLE) STYLETHIS AUCTION IS FOR OUR ONE-PIECE (NO SCREWHOLE) STYLE GRIPS. SEE BELOW. ********ONE-PIECE VS. TWO-PIECE STYLE GRIPS:A Choice for Every User! Two-Piece style grips incorporate a visible screw and screwhole, allowing easy and quick removal for cleaning or maintenance of your revolver. One-piece style grips do not use a screw but instead use an internal spacer. Both styles are traditional and historical designs and both were originally used on early Colts, so it is a matter of personal preference. Both styles of our grips will interchange and work on either style of grip frame. See below.One-Piece style grips (i.e., grips which do not have a visible screwhole in the grips) incorporate a user installed spacer (included with the grips) between the grip panels, as seen on many of the early Colts. The spacer is sent loose to ensure optimum fit with your revolver, with simple, quick installation which takes one minute or so per grip (fully illustrated instructions included). This results in a rock-tight fit, without the need of a screw. Preferred by many collectors for their clean lines and traditional look. One-Piece style grips are removed by removing the three backstrap screws, and pulling the grip and backstrap backwards. Reinstallation is in reverse order. Alternatively, our Two-Piece style grips (i.e., grips with a visible screw and screwhole) offer the superior convenience of quick grip removal. They include a free Conversion kit, allowing their use on revolvers that are currently using one-piece style grips that do not have a grip pin. The conversion kit replaces the need for a grip pin and is actually a stronger design, and allows the grips to lock up tight on the frame, allowing no movement. This requires no modification to your revolver and gives you the advantage of the ease of maintenance of Two-Piece grips, while preserving the integrity of your revolver in original factory condition. Two-Piece style grips were also used on many of the early Colts, and are a traditional and iconic historical design, offering a distinctive look and convenience preferred by many collectors.Fully illustrated, detailed instructions are included with each set of grips. 12062200~~~~~WHAT THESE WILL FIT – Please read this in its entirety (especially the note on Brass gripframes): This auction is for a set of Genuine Magna-Tusk™ grips for any of the PIETTA Model 1873 SAA (Single Action Army) style revolvers, with the standard SAA “plowhandle” grip shape.These will usually be marked “Pietta,” and may also (but not necessarily) be marked by the U.S. importer, such as “Cimarron,” “EMF,” “Taylors & Co.,” “Traditions,” etc.This includes any of the following:• Cimarron Frontier or Stainless Frontier• Cimarron El Malo (NOT the El Malo 2 – see below)• Cimarron Pistolero• Davidson’s Exclusive 1873s (sometimes also marked “Pietta 1873 Gunfighter”, “Pietta 1873 Rio” or “Del Rio Deluxe”, “Pietta 1873 Centennial”, “Pietta El Diablo”, etc.)• E.M.F. Great Western II (available in numerous variations including the Blank Firing, Buntline, Californian, Dlx Californian, Dlx Grande Californian, Cattlebrand, Dlx Stainless Steel, Express Agent (“Standard” gripframe ONLY), Frontier, Gambler’s Royale, General Patton, Gunfighter, Liberty, Midnight Special, Paladin, Pony Express (“Standard” gripframe ONLY), Posse, “R” Model, Sheriff, The Last Stand, The Shootist, U.S. Marshal, and U.S. Grant). -- Please note that these will NOT fit the “Alchimista” models – see below.• E.M.F. Hartford• E.M.F. Dakota II or Dakota III• Taylor’s & Co. Outlaw Legacy (NOT the Remington Outlaw), Single Action Stag, Cattle Brand Engraved, or other Engraved Pietta Revolvers such as Teddy Roosevelt, Patton, Cattlebrand, etc.; • Any of Pietta’s engraved SAA style revolvers being sold under various names not mentioned above, such as the Teddy Roosevelt Frontier, George S. Patton Frontier, Cimarron Buffalo Bill Cody, Cody Wild West Frontier, Bat Masterson Frontier, Outlaw Legacy, Bill Tilghman Cattleman, etc. • Traditions Single Action Frontier or Rawhide revolvers. Note: if your Rawhide revolver is the .22 cal. Rawhide Ranchhand, please send us an immediate followup email after your order and let us know. These require extra milling cutouts to mount properly to your frame.• Century Arms 1873 Millenium Please note that these will fit revolvers having the standard sized SAA style gripframe (somewhere around 3-1/16” to 3-1/8” tall depending on how you hold your ruler or tape). If it is made by Pietta, these will fit.Note: If you do not see your pistol listed, please drop us an email with your model name and we will verify your revolver. BRASS GRIP FRAMES -- IMPORTANT!*PLEASE NOTE: if you have a BRASS gripframe (such as sometimes found on the Cimarron “Pistolero”, Davidson’s Exclusive 1873s, EMF’s GWII “Gunfighter”, or Taylor’s “1873 Single Action Stag” revolvers, for example), please send us an immediate followup email after your purchase informing us that 1) your revolver has a brass gripframe, and 2) please send us the two-letter or two-number code found in the small square box stamped underneath or on the side of the receiver. This is shown in the second photo as an example. We will need this code to make sure you get the correct grips. What these WILL NOT FIT: 1. Please note that these grips are made to fit ONLY the Pietta Model 1873 style Single Action revolvers, with the typical SAA “plowhandle” shaped gripframe, and will NOT fit any revolvers from other makers (such as Uberti, Armi San Marco, Colt, Ruger, etc.). These grips will also NOT fit the Bisley, the Birdshead, the Thunderer, Thunderball, or the Lightning style revolvers, nor any of the Remington style revolvers such as the 1858, 1875, or 1890, from ANY maker, all of which use a completely different shaped gripframe. 2. In addition, these WILL NOT FIT grip frames with the taller 1860 Army style gripframe, which are around 3-1/2” tall. To make sure you are ordering the correct grips, please check your grip frame measurement prior to ordering. Your grips or grip frame should measure somewhere between 3-1/16 – 3-1/8” tall, depending on how you hold your ruler, tape, or caliper. The important thing is to make sure they are NOT around 3-1/2” tall. EMF’s Alchimista, Cimarron’s Bad Boy, or Cimarron’s El Malo 2, for example, have the taller 1860 Army style (3-1/2” tall) grip frame. If you have one of these, our Pietta 1860 Army Cap & Ball style grips are properly milled for these. Please see our store under the proper category, or email us if you cannot find what you need.Please contact us if you cannot find what you need, or if you have any questions. We are always happy to help.12062200A note on the Italian-produced Revolvers: The Italian firms, located in Northern Italy, have been making SAA style revolvers now for well over a half century, and have made a huge number of makes and models and grip frame profiles with varying configurations over the years. We have an in-depth knowledge of the differing grip configurations, have a large library of gripframe variations from the various makers both old and new, and have vast experience making grips for Uberti, Pietta, Armi San Marco, and the other Italian gunmaking firms. Our experienced makers go to great lengths to ensure an exacting fit, including utilizing modern precision CNC production techniques, as well as incorporating old-time hand tuning and hand checking the fit of every grip on our reference frames prior to leaving our factory. We have a long list of many satisfied customers in the shooting industry who have purchased grips to use in a wide variety of applications, and we can safely and confidently guarantee proper fit and finish to your complete satisfaction.For an additional charge, custom fitting is an option. Please contact us for further details if you are interested in custom fitting. 22011245 Arizona Custom Grips About Magna-Tusk™ Ivory and Stag Grips: Magna-Tusk™ Ivory and Stag grips, a product of Arizona Custom Grips, are manufactured out of our high-grade, high density ivory material designed from the beginning as a premium, high-strength grip material. Vastly superior to standard bonded ivory or stag found on most factory and other aftermarket grips, Magna-Tusk™ is capable of withstanding the heaviest recoil and impact, and is the toughest alternative grip material available today, while still retaining the pristine look of real ivory or stag. It is rock-solid, stable, and water, chemical, and oil resistant. It is flame and heat resistant, and is entirely void-free, with over 10x the strength, durability, and impact resistance of alternative materials. Unlike with real ivory or stag, there is no routine care and maintenance involved, with no danger of it drying out and cracking if not maintained properly or if left in the heat. It is filled with premium natural compounds to produce outstanding aesthetic properties and mechanical performance. When aged with our natural aging process, it takes on the equivalent of a 100-year-old patina, with subtle grain details which many experts cannot tell apart from the real thing. In addition, the material has a fine grain structure, which holds intricate detail for carvings, artistic relief work, etc., found on many historic grips. 08292000 Please note that the photo used is a stock photo (a sample pair). Yours will appear similar to these. Customer satisfaction is important to us – we guarantee your complete satisfaction with every purchase!!

Price: 79.95 USD

Location: Mesa, Arizona

End Time: 2024-02-22T17:41:21.000Z

Shipping Cost: 5.99 USD