Mustang II Power Steering Rack & Pinion w/ Offset Bushings, 82-88 T-bird Design

Description: High Quality and Durability: This Mustang II Power Steering Rack & Pinion is not a remanufactured unit, but a brand new assembly made with premium internals and seals, providing reliable performance and longevity., Versatile Fit: With the included offset mount bushing kit, this unit can fit both original Mustang II crossmembers as well as aftermarket crossmembers, ensuring a wide range of compatibility for different vehicle models., Power Steering Upgrade: The Rack & Pinion unit offers an ideal upgrade from manual steering to power steering, enhancing control at low speeds and providing additional interior room, especially beneficial in the compact interiors of street rods., Ease of Installation: The kit includes offset rack bushings and mounting hardware for straightforward installation, Mustang II Power Steering Rack & Pinion w/ Offset Mount Bushings Sku # 91603048 Mfr. Part # 91603048 Condition New Brand Speedway Motors Sold Each Details Info All-new using premium internals/seals, this is NOT a remanufactured assembly 15-1/2-inch center-to-center mounting works with aftermarket crossmembers Works with original 16-inch center-to-center Mustang II crossmembers using included offset rack bushings Offset rack bushings are not used to raise or lower the rack, but to change mounting point center distance Includes inner tie rods with SAE 9/16-18 threads installed with jam nuts 9/16-18 and 5/8-18 threads O-ring pressure and return ports Adapters to convert OE ports for use with AN -6 fittings and hose included 15:1 performance steering ratio with 2-1/2-turns lock-to-lock Pinion shaft uses industry standard ¾-inch-36 spline U-joints Upgrade Your Original Mustang II IFS with Power Rack-and-Pinion Steering There is little argument that the Mustang II independent front suspension (IFS) is one of, if not THE most widely used suspension designs for street rods, kit cars, and even updated classic muscle car suspensions. From weld-in frame stubs to full frame conversions, the Mustang II IFS offers a whole lot for your performance dollar. In one upgrade you give your project disc brakes, rack-and-pinion steering, better suspension geometry, and the ability to modify and update with all manner of aftermarket parts including drop spindles, coilover shocks, and more. Many Mustang II setups begin as budget systems with standard stamped steel control arms, small disc brakes, and manual steering. It is a great starting point and keeps the initial buy in at an enticing level for the average enthusiast, leaving plenty of room to upgrade down the road as budget allows. One extremely popular update is adding a power rack-and-pinion unit in place of the original manual Mustang II rack-and-pinion that shipped with the IFS kit. Adding power steering provides better low-speed control, especially with larger tires, and allows a smaller diameter steering wheel to be fitted, often providing much sought-after interior room in the small cabins of street rods. Our 1982-1988 Thunderbird rack-and-pinion conversion power steering rack is the perfect upgrade for when you are ready to enjoy the benefits of power steering or as an upgrade to the parts-store reman power rack provided with your Mustang II kit originally. Superior Build Quality with Direct Fit Ease Have you tried to source an original or remanufactured '74-'78 Mustang II power steering rack lately? They are getting harder to find and costs keep going up. However, a rodding trick that has grown in popularity is to upgrade to the Fox chassis Thunderbird rack-and-pinion due to its lower cost and ease of conversion. For most aftermarket Mustang II crossmembers it is a direct bolt-on swap thanks to the slotted mounting hole found on these newer crossmember designs. For those with older Mustang II crossmembers with a fixed 16-inch center-to-center mounting point distance we have put together this simple kit to help facilitate installing the newer T-Bird power rack to your crossmember. Installation is easy for the T-Bird rack by simply using the offset rack bushings and mounting hardware we have provided in this kit to change the center-to-center mounting bolt location to the wider 16-inch dimension used on the original Mustang II. Push out the included bushings (if installed) and install the offset bushings with the mounting holes outboard (away) from each other. Our T-Bird rack is not a remanufactured unit. It is built from an all-new casting and fitted with all new internals. That includes the rack gear, pinion shaft, internal seals, inner tie rods, and fluid lines. Some installations may require to properly space the rack away from the crossmember for clearance. We offer these spacers along with the required for everything to mount up properly. We provide AN -6 hose adapters for the rack's inlet and outlet ports due to the Thunderbird rack-and-pinion fittings differing from the original Mustang II rack-and-pinion fittings. This reduces frustration and installation time by allowing to be produced on site if your project is not already using AN power steering lines. The smaller 9/16-18 port is the "in"from your pump, while the larger 5/8-18 port is the return to your pump's reservoir. The T-Bird-based rack uses a 3/4-36 spline input shaft (manual is 9/16-26), requiring little more than a change at the rack end of your steering shaft in most installations. If you are replacing an older power rack, then there should be no change to your steering shaft configuration. The Perfect Solution for Most Any Mustang II Configuration A readily available power steering rack constructed from all new components and at a great value, what is not to love? Installation is a direct replacement for your manual rack in most instances due to the same Mustang II rack-and-pinion dimensions, and our T-Bird-based power steering rack will work with most any used in a modern serpentine belt drive or V-belt setup, including the Ford CII, GM Type II, and GM Type I (more commonly known as a Saginaw pump). These pumps output the necessary 1,200 psi required and flow approximately 3 GPM. We offer a multitude of in both V-belt and serpentine for Ford, GM, and Chrysler engine families to add the pump of your choice to your engine. Since there are so many variables that affect a properly functioning power steering system, including vehicle weight, alignment, steering wheel diameter, tire width, steering ratio, and much more, some applications may feel twitchy and may require a reduction in flow. The GM Type 1 and Type II pumps utilize that can easily be swapped out to adjust the flow down to aid in steering twitchiness and prevent steering dart due to an over-boosted power steering system. Another option is an where you can dial in the exact steering effort you wish easily. This means you can have the system turned down for more effort when needed for a track day, but then it is easily turned back up to reduce your steering effort for daily driving. This is your best solution when using the Ford CII pump in a Ford-powered application as well. Installation Tips Use bolt kit with rack spacers if extra crossmember clearance is needed converting from a manual rack Overall width of steering rack with inner tie rods is 45-1/8-inches Compatible with standard Mustang II outer tie-rod ends, such as Bump steer kit can be used in lieu of outer tie rods if desired If rack extensions are necessary for your installation this power rack requires 25mm-1.25 thread extensions The power steering rack has 5/8-inch and 9/16-inch O-ring style ports which will not work with inverted flare fitting-equipped power steering lines OEM replacement for 1982 to 1993 Ford Mustang, 1982 to 1988 Ford Thunderbird, and 1984 to 1988 Mercury Cougar but will require aftermarket AN pressure and return line kit to connect to your factory pump Intended for front of crossmember mounting applications only, will not work on rear mounted applications Specs Material Type Steel Sold in Quantity Kit Finish Natural Spline Count 36 Rack Type Power Thread Pitch 9/16"-18 Turns Lock to Lock 2.5 Overall Height 10.00 Overall Length 45.25 Tube O.D. 2.20 Outer Tie Rod Ends Included No Bushing Included Yes Spline OD 0.75 Spline End 3/4"-36 Overall Width 45.125 Center to Center 15.5 Thread Pitch (2) 5/8"-18 Inner Tie Rod Ends Included Yes Power Steering Pump Included No Ratio 15:1 MFG. Part # 91603048 Reviews worked as it should bolted right up to my lines Rated by bill on January 22, 2022 Summary: was having problems getting lines attached to old rack after talking to speedway we got the right rack and it went smooth after that Yes, I recommend this product. 1934 Ford Coupe Rated by Firesonny on November 29, 2021 Summary: Sell hoses with it. Yes, I recommend this product. you better have some good tools Rated by Roger on November 15, 2021 Summary: I did like the light weight of it. but i had to cut a keyway in the spline shaft for my rag joint also the spline shaft was 1 3/8" taller so i had to cut my steering shaft down and finally take a die grinder to the frontend as even with the offset kit it still needed an extra 1/8" grinded out of each side of the hole. Yes, I recommend this product. Almost right. Rated by Mopar 34 on September 22, 2021 Summary: Works with high pressure Chev power steering pump.But I had to grind the frame mounting holes out to fit the offset bushings.It comes with the adaptors to hook up the power steering hoses . Yes, I recommend this product. Yes Rated by Tom on April 03, 2021 Summary: So had to change steering shaft configuration , plus had to order a rack extension kit . Rack was not centered now so had to add 2 inches to left side to center. Just a lot of changes I didnt plan on. Cons: Input shaft was longer that mustang 2 Pros: Came quick Yes, I recommend this product. Related Items / Suggested Parts Mustang II Outer Tie Rod End, Manual Version Gotta Show 131101 Mustang/T-Bird Rack & Pinion Power Steering Hose Kit Power Steering Hose Kit for 1982-88 T-Bird Steering Rack to GM Pump Tech Support We're here to help before and after your purchase. If you have a question or need assistance with one of our products, please contact us through eBay Messaging and a knowledgeable Speedway Motors team member will be happy to help. About Speedway Motors is America’s Oldest Speed Shop® and has been a trusted source for specialty rodding and racing products and friendly expert advice for more than 71 years. Founded in 1952 by “Speedy” Bill Smith – a racer and street rodder himself – Speedway has grown from a one-man operation to become the world’s largest manufacturer, distributor and retailer of street rod and racing products. Our industry-leading fast delivery is the result of same-day shipping from our state-of-the-art, centrally located 500,000 sq. ft. headquarters. Speedway’s size offers customers unmatched product selection and low pricing, while our excellent technical support and customer service have made us a recognized leader in the rodding and racing industries.

Price: 299.99 USD

Location: Lincoln, Nebraska

End Time: 2023-11-30T13:07:32.000Z

Shipping Cost: 0 USD