Hantek Digital Oscilloscope DSO4102S 100MHz + 25MHz Arbitrary waveform generator

Description: Features:1. 2 channel digital oscilloscope + arbitrary/function waveform generator + synchronizing signal + external trigger. The keys for oscilloscope and waveform generator is separated for convenient to operate it simultaneously.2. Large and clear display (7 inch 64K color LCD display, Resolution 800x480), more clear and realistic waveform.3. Oscilloscope: 1GSa/s Sample Rate, 100MHz Bandwidth, more than 20 kinds of auto measurement functions.Powerful trigger function: edge, video, pulse, slope, over time, alternative.Arbitrary/function waveform generator: 25MHz, 12 bits resolution, 200MHz DDS, arbitrary wave/square wave/sine wave/triangle wave/trapezoidal wave/pulse wave/DC is easy to simulate transducer.Integrated USB Host, Support USB disk storage, USB interface/SD card system update.Specifications:ModelDSO4102SOscilloscopeSample RateSampling Rate Range: 1GSa/sEquivalent Sample Rate: 25GSa/sAcquisition ModesNormalNormal data onlyPeak DetectHigh-frequency and randon glith captureAverageWavefom Average, selectable 4,8,16,32,64,128InputsInputs CouplingAC, DC, GNDInpits Impendance1MΩ±2% ‖20pF±3pFProbe Attenuation1X, 10XSupported Probe Attenuation Factor1X, 10X, 100X, 1000XMaximum Input VoltageCAT I and CAT II: 300VRMS (10×)CAT III: 150VRMS(1×);Installation Category II: derate at 20dB/decade above 100kHz to 13V peak AC at 3MHz* and above. For non-sinusoidal waveforms, peak value must be less than 450V. Excursion above 300V should be of less than 100ms duration. RMS signal level including all DC components removed through AC coupling must be limited to 300V. If these values are exceeded, damage to the oscilloscope may occur.HorizontalSample Rate Range1GS/sWaveform Interpolation(sin x)/xRecord Length40KSEC/DIV Range4ns/div to 40s/divSample Rate and±50ppm(at over any ≥1ms time interval)Delay Time AccuracyPosition Range20ns/div to 80us/div; (-8div x s/div) to 40ms;200us/div to 40s/div; (-8div x s/div) to 400sDelta Time Measurement Accuracy(Full Bandwidth)Single-shot, Normal mode:± (1 sample interval +100ppm × reading + 0.6ns);>16 averages:± (1 sample interval + 100ppm × reading + 0.4ns);Sample interval = s/div ÷ 200VerticalVertical Resolution8-bit resolution, all channel sampled simultaneouslyPosition Range2mV/div to 10V/divBandwidth100MHzRise Time at BNC( typical)3.5nsAnalog Bandwidth in Normal and Average modes at BNC or with probe, DC Coupled2mV/div to 20mV/div, ±400mV; 50mV/div to 200mV/div, ±1V500mV/div to 2V/div, ±40V; 5V/div, ±50VMath+, -, *, /, FFTFFTWindows: Hanning, Flatop, Rectamgular, Bartlett, Blackman;1024 sample pointBandwidth Limit20MHzLow Frequency Response (-3db)≤10Hz at BNCDC Gain Accuracy±3% for Normal or Average acquisition mode, 5V/div to 10mV/div;±4% for Normal or Average acquisition mode, 5mV/div to 2mV/divDC Measurement Accuracy,Average Acquisition ModeWhen vertical displacement is zero, and N ≥16:± (3% × reading + 0.1div + 1mV) only 10mV/div or greater is selected;When vertical displacement is not zero, and N≥16: ± [3% × (reading + vertical position) + 1% of vertical position + 0.2div]; Add 2mV for settings from 2mV/div to 200mV/div; add 50mV for settings from 200mV/div to 5V/divVolts Measurement Repeatability, Average Acquisition ModeDelta volts between any two averages of ≥16 waveforms acquired under same setup and ambient conditionsTrigger SystemTrigger TypesEdge, Video, Pulse, Slope, Over time, AlternativeTrigger SourceCH1, CH2, EXT, EXT/5, AC LineTrigger ModesAuto, Normal, SingleCoupling TypeDC, AC, Noise Reject, HF Reject, LF RejectTrigger Sensitivity(Edge Trigger Type)DC(CH1,CH2):1div from DC to 10MHz; 1.5div from 10MHz to 100MHz; 2div from 100MHz to Full;DC(EXT):200mV from DC to 100MHz; 350mV from 100MHz to 200MHz;DC(EXT/5):1V from DC to 100MHz;1.75V from 100MHz to 200MHz;AC: Attenuates signals below 10Hz;HF Reject: Attenuates signals above 80kHz;LF Reject: Same as the DC-coupled limits for frequencies above 150kHz; attenuates signals below 150kHzTrigger Level RangeCH1/CH2: ±8 divisions from center of screen;EXT: ±1.2V;EXT/5:±6VTrigger Level Accuracy( typical)Accuracy is for signals having rise and fall times ≥20nsCH1/CH2: 0.2div × volts/div within ±4 divisions from center of screen;EXT: ± (6% of setting + 40mV);EXT/5: ± (6% of setting + 200mV);Set Level to 50%(typical)Operates with input signals ≥50HzVideo TriggerVideo Trigger TypeCH1, CH2: Peak-to-peak amplitude of 2 divisions;EXT: 400mV;EXT/5: 2VSignal Formats and Field Rates, Video Trigger TypeSupports NTSC, PAL and SECAM broadcast systems for any field or any lineHoldoff Range100ns ~ 10sPulse Width TriggerPulse Width Trigger ModeTrigger when (< , >, = , or ≠); Positive pulse or Negative pulsePulse Width Trigger PointEqual: The oscilloscope triggers when the trailing edge of the pulse crosses the trigger level.Not Equal: If the pulse is narrower than the specified width, the trigger point is the trailing edge. Otherwise, the oscilloscope triggers when a pulse continues longer than the time specified as the Pulse Width.Less than: The trigger point is the trailing edge.Greater than (also called overtime trigger): The oscilloscope triggers when a pulse continues longer than the time specified as the Pulse WidthPulse Width Range20ns ~ 10sSlope TriggerSlope Trigger ModeTrigger when (< , > , = , or ≠ ); Positive slope or Negative slopeSlope Trigger PointEqual: The oscilloscope triggers when the waveform slope is equal to the set slope.Not Equal: The oscilloscope triggers when the waveform slope is not equal to the set slope.Less than: The oscilloscope triggers when the waveform slope is less than the set slope.Greater than: The oscilloscope triggers when the waveform slope is greater than the set slope.Time Range20ns ~ 10sOvertime TriggerOver Time ModeRising edge or Falling edgeTime Range20ns ~ 10sAlternative TriggerTrigger on CH1Internal Trigger: Edge, Pulse Width, Video, SlopeTrigger on CH2Internal Trigger: Edge, Pulse Width, Video, SlopeTrigger Frequency CounterReadout Resolution6 digitsAccuracy (typical)±30ppm (including all frequency reference errors and ±1 count errors)Frequency RangeAC coupled, from 4Hz minimum to rated bandwidthSignal SourcePulse Width or Edge Trigger modes: all available trigger sourcesThe Frequency Counter measures trigger source at all times, including when the oscilloscope acquisition pauses due to changes in the run status, or acquisition of a single shot event has completed.Pulse Width Trigger mode: The oscilloscope counts pulses of significant magnitude inside the 1s measurement window that qualify as triggerable events, such as narrow pulses in a PWM pulse train if set to < mode and the width is set to a relatively small time.Edge Trigger mode: The oscilloscope counts all edges of sufficient magnitude and correct polarity.Video Trigger mode: The Frequency Counter does not work.MeasureCursor MeasurementVoltage difference between cursors: △VTime difference between cursors: △TReciprocal of △T in Hertz (1/ΔT)Auto MeasuermentFrequency, Period, Mean, Pk-Pk, Cycli RMS, Minimum, Maximum, Rise time, Fall Time,+Pulse Width, -Pulse Width, Delay1-2Rise, Delay1-2Fall, +Duty, -Duty, Vbase, Vtop, Vmid,Vamp, Overshoot, Preshoot, Preiod Mean, Preiod RMS, FOVShoot, RPREShoot, BWIDTH,FRF, FFR, LRR, LRF, LFR, LFFSignal Source ModeWaveform ImpedanceDC-25MHzSample Rate200MHzDDSOutput WaveformArbitrary wave/square wave/sine wave/triangle wave/trapezoidal wave/pulse wave/DCFrequency Resolution0.1%Waveform Depth2KSaVertical Resolution12bitFrequency Stability<30ppmWaveform Range-3.5V~+3.5VOutput Impedance50ΩOutput Current50mA Ipeak=100mASystem BW25MHarmonic Distortion-50dBc(1KHz),-40dBc(10KHz)General FeaturesDisplayDisplay Type7 inch 64K color TFT (diagonal liquid crystal)Display Resolution800 horizontal by 480 vertical pixelsDisplay ContrastAdjustable (16 gears) with the progress barProbe Compensator OutputOutput Voltage( typical)About 5Vpp into ≥1MΩ loadFrequency(typical)1kHzPower SupplySupply Voltage100-120VACRMS(±10%), 45Hz to 440Hz, CATⅡ120-240VACRMS(±10%), 45Hz to 66Hz, CATⅡPower Consumption<30WFuse2A, T rating, 250VEnvironmentalTemperatureOperating: 32℉ to 122℉ (0℃ to 50℃);Nonoperating: -40℉ to 159.8℉ (-40℃ to +71℃)Cooling MethodConvectionHumidity+104℉ or below (+40℃ or below): ≤90% relative humidity;106℉ to 122℉ (+41℃ to 50℃): ≤60% relative humidityAltitudeOperating: Below 3,000m (10,000 feet);Nonoperaring: Below 15,000m(50,000 feet)MechanicalPackage SizeLength 385mm, Width 200mm, Height 245mmWeight3.0KG(with Packing); 2.06KG(without Packing)Material: ABS Bandwidth: 100MHz Plug Type: EU / US (Optional) Power Supply: AC220V~240V 50Hz / AC100~120V 60Hz Oscilloscope Probe Model: PP-150 Length of the Powerline: Approx. 150cm / 59.1in Length of the USB Line: Approx. 107cm / 42.1in Length of the Probe Line: Approx. 130cm / 51.2in Size of the Oscilloscope Body: Approx. 31.5 * 12 * 15cm / 12.4 * 4.7 * 5.9in (L * W * H) Oscilloscope Weight: 2.06kg/ 4.6lb Package Size: Approx. 38.5 * 19.5 * 24cm / 15.1 * 7.7 * 9.4in Package Weight: 2.97kg/ 6.6lb (2972.6g/104.8oz) Package List: 1 * Digital Storage Oscilloscope 2 * Oscilloscope Probe 1 * Oscilloscope Powerline 1 * Hantek Data CD 1 * USB Line 1 * BNC to BNC Wire

Price: 349.99 USD

Location: 深圳

End Time: 2023-10-28T16:49:11.000Z

Shipping Cost: 0 USD