For Triumph Rocket III Touring ALL Motorcycle Gear Indicator Digital Gear Meter

Description: Welcome to Knightshousestore We are a conpany with more than 10 years ecperience in the priduction of motorcycle accessoruies manufacturers. Our GFYSHIP brand has a high popularity and evaluation. If you have any product you want. Please contact us and we will help you find it. We also have our own factory. You can customize the products you need. We will bring you satisfied with the service cheap price waiting for you. Product Description Note when placing an order: The gear indicator has three colors, red, green, and blue. If you have a favorite color, please place an order and note your favorite color. If there is no note color, our gear indicator will be red by default. Best wishes Note: Disclaimer: Do not attempt to install the product if you don’t have basic mechanical skills!!! The product has a version with a mounting bracket and a version without a mounting bracket. Please choose the product that suits you according to your actual situation. Please note that for product beauty, products with mounting brackets do not have the word 'Gear' on the top of the surface. Special Function: Touch Sensor Robust Design High Speed Warning Auto Brightness Control Flipping the display upside down No need to cut any wires and no need for soldering Even if you do not run the motorcycle, you can complete the product settings. The setting can be completed when the motorcycle is completely stopped. Sign Description: C: Code Reading the firmware version L: Learning Learning the gear positions F: Filtering Adjusting the filtering (sampling period) b: Brightness Adjusting the sensitivity of the light sensor H: HSW High Speed Warning function E: ESW Engine Speed Warning function Upside down Flipping the display upside down Defaults Resetting all values to factory defaults Features: Condition:100% Brand New Light Color: Red/Blue/Green 1-6 Level IP68 Waterproof Gear display The Fact: FAST AND ACCURATE Instant and accurate indication of the selected gear (right after the clutch is released) for added control and safety. The sampling period can be adjusted to make the response quicker or slower, depending on shift speed and signal conditions. TOUCH SENSOR All settings can be done via the touch sensor so there’s no opening on the housing, it is completely sealed and encapsulated in epoxy. The touch sensitive area is on the TOP of the unit. However, after programming, the unit can be mounted even with the top side stuck to the dashboard (via the sticky pads supplied) and will function properly. It can also be used with the optional GFYSHIP Mount. AUTO BRIGHTNESS CONTROL The brightness of the display is adjusted automatically according to the ambient light intensity. The sensitivity of the sensor can be fine-tuned in the menu. HIGH SPEED WARNING FUNCTION If you wish, you may set the unit to warn you when the set road speed and/or the set engine speed is exceeded. ROBUST DESIGN - Full SMT-design, encapsulated in epoxy - Flash memory to store user settings even with the battery disconnected - Only inspected, high quality components are built in - Each unit is extensively tested prior to shipping Fitment: For Triumph Rocket III Touring ALL YEARS Installation: 1. Gain access to the Gear Position Switch (GPS) connector. 2. Disconnect the GPS coupler. Make sure the gearbox is in Neutral and turn the ignition switch ON. Wait a few seconds. The Neutral indicator should NOT be lit with disconnected GPS coupler. After confirming this, turn the ignition OFF and proceed to the next step. 3. Connect the GFYSHIP plugs to the 3-pole plug adapters. 4. Neatly route the GFYSHIP cable from the plugs to the mounting location, preferably along the frame. Do not route the harness very close to the exhaust pipe or cylinder head. 5. Connect the GFYSHIP Red wire to an ignition switched +12V power lead by using the Red wire tap connector supplied. Set Up: Note: If the unit does not indicate the gears correctly with the pre-set gear position values, you’ll need to start the Learning procedure.The TOP side of the housing is the touch sensitive area so it must be kept free, away from all objects. If the unit is in a mount, remove it first. - Have the gearbox in Neutral. - Have the ignition OFF (the display must be blank). - Turn the ignition ON and the engine stop switch to RUN position (the display should count up and then show “0”). Wait at least 2 seconds. - With your index finger (without gloves) tap the top side of the unit and hold your finger until the first menu sign shows up. Remove your finger now. Note: If the gearbox is switched to a gear then accessing the menu will be disabled even if you shift back to neutral. Cycle the ignition key to start overIf the unit does not indicate the gears correctly, start the Auto-Learning procedure. Perform the steps either in the garage with the engine running (put the bike on a rear stand) or while riding normally. In the menu, select the “L” sign and do a long tap. 5. When you see the “1” sign flashing, select 1st gear. The “1” sign starts flashing faster, indicating that the learning is in progress. 6. When you see the “n” (next) sign, select the next gear. The gear number starts flashing faster when the unit is learning the new gear position. Repeat this step until all gears have been taught. Note: If you’d like to cancel or start over the process, turn the ignition key off. Keep riding in top gear until the “U” (update) sign starts flashing (if your bike has 5 gears only, it takes longer, about 15s). The unit is now programmed and should indicate all gears correctly.

Price: 84.01 USD

Location: Nanyang City,Henan Province

End Time: 2024-10-10T07:22:35.000Z

Shipping Cost: 0 USD