Cross Hatch Adhesion Tester Instruction Cross-Cut Tester Kit USG

Description: Note: Please contact us before purchasing the item. After confirming product detailed info & delivery time, then placing the order, thus it will save lots of time and avoid trouble. Thank you. NOTE： we don't ship the item to PO BOX address， and we only ship the item to English address, so please leave us your physical English address when you pay. Great QFH Cross Hatch Adhesion Tester Instruction Cross-Cut Tester Kit USG New UsesThe instrument is mainly suitable for organic coating adhesion assay Hatch.Applies not only to the laboratory,the construction site can also be used under various conditions.Working principle and scope The instrument is a certain specification tool that will make the coating lattice graphicscut and penetrate,hatch completed by six graphic classification, assess the effect of the coating adhesion separated from the substrate.Technical Specification 1.Multi-blade cutter spacing are: 1+0.01mm, 2+0.01mm. 2.Multi-blade cutter addendum straightness were: ≯0.003mm≯0.006mm. 3.Multi-blade cutter working tooth tip width: ≯0.05mm.Instruction 1.The specimen must be prepared according to ISOR1514 and ISO2828 requirements.2.The test piece is placed on the tablet hardness sufficient.3. Handheld Hatch handle, so multi-blade cutter perpendicular to the specimen plane.4.With uniform pressure, steady approach does not vibrate and 20-50mm / S cutting speed cutting program.5.The specimen is rotated 90 degrees on the cutting stroke cuts repeat the above operation,so as to form a lattice graphics.6.With a soft bristle brush on both sides of the diagonal lattice pattern gently back 5 times,5 times forward brush specimens.7.The test at least at three different locations on the test piece is completed,if the test results of three different positions, the experiment should be repeated at more than three positions, all while recording the results.To replace the multi-blade cutter, use a screwdriver blade Loosen the two screws,put the knives, knife blade attached to the handle side of the site, and tighten the screws.Please Attention 1.All cuts should be through the coating, but not too deep cut substrates.2.As a result of the coating is too thick and hard and can not penetrate thematerial in the end,the experiment is not valid, but it should be stated in the test report.3.The test must be a US company 3M tape produced 610-1PK special tape test(or otherwise specified test tape). The tape posted on the whole cross hatch, and then tore off the minimum angle, the result may be in proportion to the gum off the area determined according to the film surface.4.The test should be carried out at a temperature of 23 ± 2 ℃ and relative humidity of 50 ± 5%. Package Included: 1 x Brush 3 x Blades( 1 x 1mm 11 teeth，1 x 2mm 11 teeth，1×3mm 6 teeth) 1 x Cross Hatch Cutter 1 x Magnifier 1 x Carry Box 1 x1 roll of 3M Transparent Tape Shipping PolicyWe will send out the item within 2-3 days through DHL/EMS/FEDEX /UPS/SPEEDPAK/CHINA POST to the below countries:Belgium, Netherlands, Luxembourg, Italy, Germany, France, United Kingdom, San Marino;Austria ,Denmark ,Finland ,Greece ,Ireland ,GUERNSEY ,JERSEY ,Norway ,Portugal , spain , Sweden , Switzerland;Bulgaria,Cyprus,Estonia,Latvia,Lithuania,Malta,slovakia,slovenia;Czech Republic, Hungary, Poland, Romania,.Australia ,New Zealand ,Korea South, Malaysia, Thailand, Philippines ,Singapore , Bruniei ,Taiwan , Macau, Indonesia,USA, CanadaWe will send tracking number to your eBay email within 1 day after sending out your itemWe will mark the item at the very low value, so that you do not need to pay for the tax or pay a little tax. Payment policy:We accept Paypal only.Payments must be finished within 5 working days after bid, otherwise, Unpaid Item dispute will be reported to eBay.Refund &Return policyWe take all the responsibility during delivery. If you do not receive your item, we will refund you the full money or send you a new item according to your request.We can accept the return item within 60 days after the buyer receives it. Once we receive the return item, then we will refund you full money. Feedback Policy We will very appreciate you give us positive feedback ASAP. If the item you got in any problem, PLS don’t hesitates to contact us. We will do our best to help solve the problem

Price: 85.62 USD

Location: zhengzhou henan

End Time: 2025-02-01T01:23:34.000Z

Shipping Cost: 0 USD